Pilot Courses of Instruction

Flight Instruments

Steve Sconfienza, Ph.D.

Airline Transport Pilot

Flight Instructor: Airplane Single and Multiengine; Instrument Airplane

cell: 518.366.3957

e-mail: docsteve@localnet.com

Altimetry, Airspeed, & Related Information

Altimitry

Terms

Indicated Altitude
Altitude as read directly from the Altimeter (generally when it is set to the current local altimeter setting, QNH).
Calibrated Altitude
Indicated Altitude corrected for installation and positional error.
True Altitude (QNH)
Calibrated (or Indicated) Altitude corrected for non-standard temperature: true height above Mean Sea Level (MSL).
Pressure Altitude (QNE)
Altitude with respect to standard pressure (standard datum plain).
Density Altitude
Pressure Altitude corrected for air non-standard temperature.
Absolute Altitude (QFE)
Altitude with respect to the surface.

Standard Day

Standard Pressure
1013.2 millibars / 29.92 in. Hg
Standard Temperature
+15 deg. Celsius / +59 deg. Fahrenheit

On a standard day at sea level, calibrated altitude, pressure altitude, true altitude, and density altitude will all be equal.

Errors

From High to Low, Look out Below

When flying from areas of high temperature or high pressure, the airplane, with no corrections made, will follow a constant datam plane downward: that is, the altimeter reading a constant altitude, will lead the pilot to correct altitude (in absolute terms) downward (see figure one). Altitude errors of as much as 20% have been estimated (see IFR Exam-O-Grams).

When flying from an area of high pressure to low pressure, the effect of following a standard datum is negated by using enroute altimeter settings.

There is no practical way of directly reading altitude corrected for temperature, so following a constant indicated altitude can cause aircraft to come dangerously close to the ground or other obstructions enroute.

NOTE: Obstacle altitudes on charts are in true altitude.

Figure One: Altitude Data Planes with respect to temperature
chart of air pressure data planes with respect to temperature

Figure Two: Altitude Data Planes with respect to pressure

chart of air pressure data planes with respect to pressure

Airspeed

Terms

Indicated Airspeed (IAS)
The airspeed shown by an airspeed indicator (uncorrected).
Calibrated Airspeed (CAS)
Indicated airspeed corrected for instrument installation error.
Equivalent airspeed (EAS)
Calibrated airspeed corrected for compressibility error.(*)
True airspeed (TAS)
Equivalent (or Calibrated) airspeed corrected for error due to air density (altitude and temperature & pressure variations).
Groundspeed (GS)
Actual speed of the airplane over the ground — this is the TAS adjusted for the wind vector.

Notes

(*)

Equivalent airspeed:

Compressibility is a higher altitude, higher speed phenomenon. Compression becomes a factor over about 10,000 feet and 200 knots. See a typical Compressibility Correction Chart.


Pitot-Static System

Care

The pitot-static system has two aspects that are open to the outside of the aircraft: the pitot tube, which measures the ram-air pressure of the forward motion of the aircraft, and the static port, which measures the ambient air pressure. The pitot tube (or tubes) will be found generally under the wing facing forward. The static port (or ports) will be found on the side of the aircraft or as part of the pitot tube. Both must be clear of all dirt and other obstructions. There is also usually an alternate static source inside the aircraft. Visual inspection during the the preflight inspection is sufficient to ensure that the pitot tube and static port are superficially clear, but the first operational indications will not be visible until the takeoff roll.

Understanding Operation

Fundamentals

Briefly stated, the pitot-static system drives three instruments: the altimeter, the airspeed indicator, and the vertical speed indicator:

Correct Operations: Initial Indications

  1. On the ramp and during taxi,

    the airspeed indicator (ASI) and vertical speed indicator (VSI) will read zero (knots and feet per minute); the altimeter will read field elevation when set to the local altimeter setting.

  2. From position on the runway, or from a rolling start, into the takeoff roll,

    the VSI and altimeter should show no change and the ASI should show a smooth increase from zero.

  3. At rotation,

    the VSI and altimeter will start to show a climb; the ASI will continue to indicate a steady increase.

  4. In initial climb,

    the VSI and altimeter will continue to show a climb; with an established climb attitude, the ASI and VSI will stabilize on a steady value and the altimeter will stabilize at an apparent steady rate of change

If any of these observations fail, especially the last, the indication is that the system has failed.

Understanding Failures

Instruments may fail and tubes may leak, but there are two systemic failures that can be anticipated that cause potentially catastrophic failures: both involve blockages, one of the pitot tube and the other of the static port. In flight, these are both most likely to be caused by icing.

Blocked Static Port

This condition will prevent there from being any indication of changes in altitude (no static air source means the system is sealed: no altitude change and no indication of vertical speed). Many aircraft, especially those intended for instrument flight, will have an alternate static source located in the cockpit.

While there will be no indicated change in altitude, the airspeed indicator will indicate a decrease with an increase in altitude while holding airspeed constant (higher altitude means less ram-air pressure for a given constant airspeed); conversely, it will incorrectly indicate an increase in airspeed with a decrease in airspeed.

Changes in deck-angle and airspeed at constant power with no corresponding change in altitude indicates a blocked static port.

Establish a safe attitude and ignore airspeed, altitude, and vertical speed indications: open the alternate static port (if installed) for altitude and vertical speed.

Blocked Pitot Tube

A blocked pitot tube (often from ice) will have no affect on the static part of the system (altimeter and vertical speed indicator) but will cause the airspeed indicator to give erroneous indications. In this situation, with the pitot system sealed, changes in altitude will indicate changes in airspeed with airspeed actually held constant: an increase in altitude will indicate an increase in airspeed (constant pressure in the ram-air portion of the system against decreasing pressure in the static portion of the system); conversely, a descent will indicate a lower airspeed (constant ram air against increasing static air). These present critical and dangerous situations: flight crews have pitched their aircraft up into stalls believing their airspeed was dangerously high when in fact they had neglected to turn-on the pitot heat and were climbing with a blocked pitot tube.

Increasing airspeed during a climb or decreasing airspeed during a descent at constant power and deck-angle indicates a blocked pitot tube.

Establish a safe attitude and ignore airspeed indications: altitude and vertical speed will be correct.